Two-head screw-assisted weighing for measured portions and two-product mixing
The 2 Head Screw Linear Weigher supports controlled weighing tasks. This machine provides controlled screw feeding for measured packaging portions. Two weighing heads form the documented arrangement for portion preparation. The stated configuration is referenced as model WL P2H50A. It prepares measured portions before transfer toward a receiving package. Screw feeding guides material movement into the documented weighing stage. Product behavior remains important when planning a practical feeding routine. Target weight helps define the intended portion for each package. Receiving equipment should accept each discharged portion without disrupting material flow. This configuration provides defined machine facts for packaging line discussions.
The 2 Head Screw Linear Weigher lists a 100–3000 gram range. That documented range identifies the stated portion weight envelope. The listed weighing accuracy range is one to twenty five grams. Accuracy expectations depend on material characteristics and operating conditions. Material consistency affects how screw feeding reaches each weighing head. A target portion should match the documented range before configuration discussion. The machine description does not provide separate values for every material. Actual settings should reflect the physical behavior of intended product. Measured portions then move onward to the selected packaging stage. These specifications provide a factual starting point for application planning.
The 2 Head Screw Linear Weigher includes a documented five liter hopper. Hopper capacity describes the listed holding volume at this stage. Screw feeding is relevant where material movement needs deliberate control. Feed consistency should be considered before setting a desired output rate. Observe whether material enters the screw stage at steady intervals. Irregular supply can affect the practical flow through weighing operations. The two head arrangement supports the documented measured portion process. It also lists a maximum of two mixed products. Material combinations should be considered according to their physical behavior. The receiving package needs a suitable handoff from discharge.
The 2 Head Screw Linear Weigher uses the listed MCU control system. A seven inch touch screen provides the documented operating panel. Ten preset programs are included in the stated product information. Preset programs can organize repeatable setup discussions for recurring products. Operators should review settings when material conditions or target weights change. The control interface should remain accessible within the planned installation layout. Daily work also includes observing feed behavior and discharge conditions. Cleaning routines should reflect the material and surrounding packaging process. Changeovers require attention to the product combination and intended portion. These points describe normal operation without claiming unlisted automated functions.
The 2 Head Screw Linear Weigher lists two to fifteen bags minute. This is the documented maximum speed range for the machine. Rated speed alone does not demonstrate stable output during production. Material supply and downstream transfer influence the practical packaging flow. Begin with whether screw feeding remains steady at the required portion. Then consider how each measured portion reaches the receiving package. A stable handoff supports orderly movement through the next stage. Production targets should be discussed with material behavior and pack format. The specified speed gives context rather than a guaranteed result. Line conditions determine how the documented range applies in practice.
The 2 Head Screw Linear Weigher requires AC 220V power. The documented supply tolerance is plus or minus ten percent. The listed frequency is fifty or sixty hertz. Packaging weight is documented as one hundred eighty kilograms. Installation planning should allow adequate space for operation and access. Operators need clear access to the touch screen panel. Material supply should be positioned to support consistent screw feeding. The receiving station should align with the discharged measured portion. Electrical supply should be checked against the intended site arrangement. These listed details help position the machine within a packaging workflow.
The 2 Head Screw Linear Weigher can serve measured portion workflows. It may be considered before a vegetable packing machine stage. Vegetable form and feeding behavior require separate application consideration. The weigher does not establish downstream vegetable packing machine capability. It may also connect with a rotary packaging machine project. Rotary packaging machine requirements determine the necessary receiving interface separately. A small sachet packing machine may be another downstream consideration. Small sachet packing machine format must match the portion transfer arrangement. Each wider line needs planning around material supply and discharge. The weighing stage remains focused on documented screw fed portion control.
The 2 Head Screw Linear Weigher supports two product mixing discussions. The stated maximum is two mixed products for this configuration. Each material should be reviewed for its feeding and weighing behavior. Target relationship between ingredients should reflect the intended finished package. The available information does not define every possible material application. Discuss product condition before treating any option as applicable. A practical review includes target weight and expected output. It also includes packaging format and available installation space. Operator access supports normal setup observation and routine adjustment. These application details help align documented equipment with actual requirements.
The 2 Head Screw Linear Weigher should be discussed with material details. Share the material type and its observed feeding behavior. Provide the desired target weight for each finished portion. Include expected output and the receiving packaging format. Describe available installation space and access requirements for operators. Identify whether two product mixing is needed for the application. Explain how material will be supplied to the screw stage. Note the preferred connection to downstream packaging equipment. These details support a focused conversation about documented machine configuration. They also help relate the weighing stage to everyday operation.
See the real-world impact of Echo Machinery. Read how our proven platforms and flexible customization have helped distributors and manufacturers scale their businesses.
EN
